16” Stand Fan with
Remote Control
Model No: FS3-40R-30
FEATURES
ꢀ Remote Control
ꢀ 3 Speed Settings
ꢀ 4 Hour Auto-off Timer
ꢀ Oscillation
ꢀ LED Display Panel
ꢀ Adjustable Height
ꢀ Adjustable Tilt Head
ꢀ Whisper Quiet Operation
ꢀ Contemporary Design
3122242
WARNING:
To reduce the risk of fire, electric shock or personal injury, all wiring and grounding must conform to
the latest edition of Local and National Electrical Codes. It is the customer’s responsibility to have
the wiring and fuses checked by a qualified electrician to make sure adequate electrical power is
available.
TECHNICAL SPECIFICATIONS
Voltage Rating
Power Consumption
Unit Size
120V, 60Hz
50W
17 in. (W) x 16 in. (D) x 53.5 in. (H)
12.4 lbs
Unit Weight
3
This product employs overload protection (fuse). A blown fuse indicates an overload or short-circuit
situation. If the fuse blows, unplug the product from the outlet. Replace the fuse per the instructions
below and check the product. If the replacement fuse blows, a short-circuit may be present and the
product should be discarded or returned to an authorized service facility for examination and/or
repair.
HOW TO REPLACE THE FUSE
1. Unplug the fan from the outlet. Place the plug on a firm, flat surface.
Open the fuse cover, located on the top of the plug, using your thumb
or a flathead screwdriver to slide the over towards the prongs.
NOTE: Ensure that the fuse cover is completely open before attempt-
ing to remove the fuse.
2. Remove the fuse carefully by using a small screwdriver to pry the fuse
out of the compartment by the metal ends of the fuse.
3. Risk of fire. Insert a new 5 Amp, 125 Volt fuse into the fuse compart-
ment, making sure that the fuse is securely in place.
4. Slide the fuse cover closed completely. If the fuse cover is difficult to
close, make sure the fuse is properly secured in place by pressing
down on the metal ends of the fuse.
CAUTION: Risk of fire. Do not replace the attachment plug. It contains a
safety device (fuse) that should not be removed. Do not use the product if
the attachment plug is damaged.
To avoid a risk of fire, only replace with a 5 Amp, 125 Volt fuse.
To order a new fuse, contact Soleus Air at (888) 876-5387.
4
ASSEMBLY
WARNING: DO NOT plug in fan before assembly.
Tools required: Phillips screwdriver (not included)
Base and Pole Assembly:
1. Unscrew the “L” screw from the bottom of the lower pole. Slide the bottom of the lower pole into the
hole on the base. Use the “L” screw removed earlier to secure the pole to the base.
2. Now slide the top pole (the piece that contains the control panel and fan head) onto the chrome end of the
lower pole that was just inserted into the base. Secure these pieces together using the fastener on the back
of the top pole.
Fan Head Assembly:
Unscrew the mounting nut counter clockwise from the motor shaft.
Position the back grill over the motor shaft, fitting the holes in the
back grill over the knobs that protrude from the front of the mo-
tor. Make sure the rear grill fits securely against the motor housing.
Secure the back grill by screwing on the mounting nut. Turn clockwise
and tighten firmly.
Slide the fan blade onto the motor shaft with the fan blade’s shaft
sleeve facing the motor. Make sure the groove in the shaft sleeve
fits over the spring bolt on the motor shaft.
Attach the fan blade by screwing the securing knob onto the motor
shaft counter clockwise.
Position front grill so logo is horizontal. Attach the grills together by
positioning the top tab of the front grill over the back grill. Firmly
press the black ring of the front grill onto the back grill, snapping
into place. This completes the assembly.
5
OPERATING INSTRUCTIONS
Using Fan Controls
1. Set the fan on a stable, level surface.
2. Turn the fan on by pressing the ON/SPEED button located on the control panel or the included Remote
Control.
3. Adjust the speed setting by pressing the ON/SPEED on the control panel or the remote control. This fan
has 3 speed settings. Each press of the ON/SPEED button will change the speed setting on the fan. The
LED lights above the ON/SPEED button will light up when the corresponding speed is selected.
4. To oscillate the fan head, press the SWING button located on the fan control panel or the SWING button
on the remote. Each press of the oscillation button will change the oscillation pattern.
5. This fan includes a 4 hour auto shut-off timer. To operate the timer, press the TIMER button located on
the remote control. Each press of the TIMER button on the remote will change the time for the fan to auto-
matically shut-off. Press the TIMER button once and the fan will be set turn off in one hour. Press the
timer twice and the fan will shut off in two hours, press the timer 3 times and the fan will be set to turn off
in 4 hours.
6. To turn the fan off, press the OFF button on the fan, or the OFF button on the remote control until the unit
turns off.
Adjusting Height and Fan Head Tilt
1. To adjust the height of the fan, turn the fan off and unplug the unit, turn the Adjustable Height Knob (L)
counter-clockwise to loosen the stand. Adjust the fan to the desired height, then firmly tighten to secure
into place.
2. To adjust the tilt on the Fan Head, turn the fan off and unplug the unit, tilt the fan head forward/back by
pulling or pushing the top of the Fan Grill. The fan will make a clicking noise while being adjusted.
6
CLEANING & MAINTENANCE
1. Turn the fan off and unplug the unit.
2. Wipe the fan down with a damp cloth for most efficient operation.
3. Air dry the fan completely before use.
4. Never use abrasive cleaning agents or solvents. This may cause damage or deterioration to the surface of
the unit.
5. Do not immerse the fan in any form of liquid. Do not allow water to drip on or into the fan motor
housing.
Fan Blade Cleaning:
• Make certain the fan is unplugged. Unlock the metal clips on the front grill and remove the front grill. Use
a Phillips screwdriver to loosen the securing screw and remove the fan blade.
• The fan blade and grill may be cleaned with a damp cloth and mild detergent.
• Reassemble the fan after the parts have dried completely. To do so, replace the fan blade, tighten the
securing screw, and secure the front grill. Do not plug the fan into an electrical outlet until it is fully
reassembled.
STORAGE
If the fan will not be used for a long period of time, store it in a cool, dry location when not in use. To
prevent dust and dirt build-up, use the original packaging to repack the unit.
OVERHEAT PROTECTION
A thermostat is built-in to the motor to prevent overheating. If the fan temperature exceeds the limit on the
thermostat, the fan will automatically shut-off to prevent overheating and protect the fan components from
damage.
REMOTE CONTROL
The supplied remote uses 2 “AAA” batteries. The remote will work at a distance of roughly 25 feet, and an
angle of 60°.
7
WARRANTY
One Year Limited Warranty
Soleus International Inc. warrants the accompanying Soleus Air FS3-40R-30 16” Stand Fan to be free of defects in ma-
terial and workmanship for the applications specified in its operation instruction for a period of ONE (1) year from the
date of original retail purchase in the United States.
If the unit exhibits a defect in normal use, Soleus International Inc. will, at its option, either repair or replace it, free of
charge within a reasonable time after the unit is returned during the warranty period.
As a condition to any warranty service obligation, the consumer must present this Warranty Certificate along with a
copy of the original purchase invoice.
THIS WARRANTY DOES NOT COVER:
•
Damage, accidental or otherwise, to the unit while in the possession of a consumer not caused by a defect in
material or workmanship.
•
Damage caused by consumer misuse, tampering, or failure to follow the care and special handling provisions
in the instructions. This includes dents, accidental or otherwise, to the base and head of the unit.
•
•
Damage to the finish of the case, or other appearance parts caused by wear.
Damage caused by repairs or alterations of the unit by anyone other than those authorized by Soleus
International Inc.
•
Freight and Insurance cost for the warranty service.
ALL WARRANTIES, INCLUDING ANY IMPLIED WARRANTY OF MERCHANT ABILITY ARE LIMITED TO
ONE-YEAR DURATION OF THIS EXPRESS LIMITED WARRANTY. SOLEUS INTERNATIONAL INC.
DISCLAIMS ANY LIABILITY FOR CONSEQUENTIAL OR INCIDENTAL DAMAGES AND IN NO EVENT
SHALL SOLEUS INTERNATIONAL INC’S LIABILITY EXCEED THE RETAIL VALUE OF THE UNIT FOR
BREACH OF ANY WRITTEN OR IMPLIED WARRANTY WITH RESPECT TO THIS UNIT.
This warranty covers only new products purchased from our authorized dealers or retailers. It does not cover used, sal-
vaged, or refurbished products.
As some states do not allow the limitation or exclusion of incidental or consequential damages, or do not allow
limitation on implied warranties, the above limitations and exclusions may not apply to you. This warranty gives you
specific legal rights, and you may also have other rights that vary from state to state.
For Technical Support & Warranty Service
Please Call (888) 876-5387
Or Write To:
Soleus International Inc.
20035 E. Walnut Dr. North.
City of Industry, CA 91789 USA
8
|